Diy Furniture Ideas For How to Make Cabinets Taller – Free Plans & Video Tutorial – Shanty 2 Chic

We are back again with the third part of our sisters Shanty House Crash series! This project is all about How to Make Cabinets Taller! We are taking Leasha’s builder grade cabinets and adding height! This was a cheap and great alternative to buying completely new cabinets and/or cabinet doors! With just a few sheets of hardwood plywood, a few boards, a few tools and some elbow grease, we not only added height to her cabinets, we completely updated the style of her kitchen! Just click the Play Button below to watch the entire process!

How about that?! Such a huge difference for so little money!

Keep in mind that this set of plans was designed specifically for Leasha’s cabinets. Make sure to adjust the measurements and supplies to fit your own cabinet design. This set is a great reference to make your modifications, as her cabinets are a standard size.

Here are the cabinets before!

Here’s a bit of the step-by-step process, as well! You can get the FREE Printable Plans at the end of this post!

Step 1 – Remove the Trim and Add New Trim

How to Make Cabinets Taller

The first step was to remove the crown trim from the cabinets. Next, we cut the edge-glued pine to size and attached it to the top of the cabinets with 1 1/4″ brad nails and wood glue. We used our Ryobi 18-gauge Brad Nailer to attach.

Make Cabinets Taller

Once the base piece was installed, we added a small stick of trim to the front of the cabinets. This was to cover up where we took the original crown piece off. The size of trim that you use will depend on how much space you have between the cabinet doors and the base piece.

Step 2 – Build the Hood Cabinet

Make Cabinets Taller

With the base piece and trim attached, we began to build the middle box that we will call the “hood cabinet”. We cut the hood boards to size and drilled 3/4″ pocket holes into the ends of each support piece and the bottom end of each side piece. You can find our favorite model of Kreg Jig HERE!

Make Cabinets Taller

Then, we attached the supports to the front of the side pieces with 1 1/4″ pocket hole screws and wood glue. Make sure to refer to the plans for the placement of the support pieces. This box will cover the existing hood vent that has been drywalled over. If you kitchen does not have this, you can put supports on the back side of the hood cabinets, as well.

Make Cabinets Taller

Once the hood was assembled, we cut a piece of 1/4″ hardwood plywood to size. We attached it to the supports with wood glue and 3/4″ staples, using our Ryobi 18-gauge stapler.

Make Cabinets Taller

Next, we cut the hood face frame pieces to size and attached them the front of the hood with 1 1/4″ pocket hole screws and wood glue.

Make Cabinets Taller

We brought the hood cabinet inside, slid it into place and attached it to the base piece with 1 1/4″ pocket hole screws and wood glue.

How to Make Cabinets Taller - The Hood Cabinet

Hood Cabinet – DONE!

Step 3 – Build the Cabinet Shelf Boxes

Make Cabinets Taller

We moved onto the cabinet shelf boxes. These are both constructed the same way but one is longer than the other. We cut the open cabinet pieces to size and drilled 3/4″ pocket holes into the ends of each shelf piece and the bottom ends of each side piece.

Make Cabinets Taller

We attached the shelf pieces to the side pieces with 1 1/4″ pocket hole screws and wood glue. The pocket holes should face down on the bottom piece and up on the top piece. Make sure the pocket holes on the side pieces face in!

How to Make Cabinets Taller - shelves

We brought the cabinet boxes inside and slid them into place before attaching the face from pieces. We attached the face frame pieces with 1 1/4″ pocket hole screws and wood glue.

Step 4 – Sand & Paint

Once all of three boxes were installed, we filled all of our holes with wood filler (find our favorite wood filler HERE), gave it a good sanding and a couple of coats of paint!

You can find the paint that we used to paint the cabinets HERE!

Now for the before:

Make Cabinets Taller

And the after!

Make Cabinets Taller
Make Cabinets Taller
Make Cabinets Taller
How to Make Cabinets Taller
How to Make Cabinets Taller

Love this DIY project so much! Getting rid of that 3 foot blank space of wall, adding storage and adding height to her cabinets, all in one! This was a super inexpensive project and an easy DIY for anyone!

Linking to all the sources below!

Faucet

Rug

Mugs

Mug Holder

Cabinet Pulls

Flooring

Cabinet Paint

Kreg Jig

Make sure to download the FREE printable plans HERE!

Make sure to subscribe to our Youtube Channel HERE so you don’t miss any of our how-to videos! You can see the rest of this #shantyhousecrash below!

How to Make Cabinets Taller

Leave a Reply

Your email address will not be published. Required fields are marked *